Liste der Anhänge anzeigen (Anzahl: 1)
ASA Einstellrad an Electro 35 GSN.
Moin Euch.
Tja, so wie es aussieht habe ich mich mal wieder in die Nesseln gesetzt !
Heute Morgen kam meine bei Ebay Kleinanzeigen erworbene Yashica Electro 35 GSN an.
Ich ließ sie jetzt erst mal ein paar Stunden auftauen.
Film eingelegt, Kamera angeschaltet. Und nun wollte ich den ASA Wert 200 festsetzen. Leider drehte sich mit dem Außenring auch die innere Scala mit. Blieb immer auf 800.
Dann tippte ich mal auf die kleine Schraube in der Mitte und, Boing, kamen mir Schräubchen, Scalenscheibe und Federblatt entgegen.
Ich schraubte alles wieder ein, Federblattfalzen zeigten nach unten, aber es blieb dabei. Kein ablesbarer Wert ein zu stellen.
Ich habe nun wieder alles abgeschraubt und den Außenring auf Anschlag links (von hinten betrachtet) gedreht.
Nun wollte ich mal fragen wie Ihr dieses Problem lösen würdet ?
Hoffentlich kann der Film drinnen bleiben da er neu ist.
Danke Euch,
Lefty...
Liste der Anhänge anzeigen (Anzahl: 2)
Dieses Teil bitte 1x in scharf und dann 1x umdrehen und in scharf
Anhang 142011
dann hier hingucken und zur Not braucht es die Kragle-Geheimwaffe um das aufnehmende Gewinde in der Kamera zu fixieren
Anhang 142012
https://en.brickimedia.org/wiki/Kragle
Liste der Anhänge anzeigen (Anzahl: 5)
So, ich habe nun mal die von Jan verlangten Bilder gemacht.
Und falls da Fragen auftauchen auch gleich etwas mehr.
Anhang 142022
Liste der Anhänge anzeigen (Anzahl: 3)
Zitat:
Zitat von
Bessamatic
Hier im Video ab ca. 18:30 wird die Montage erklärt, auch wie man die max. ISO erkennt.
https://www.youtube.com/watch?v=lZ7xE4X3C_I
Dreht die Achse denn mit? Sollte ja alles stabil in der Lage sein, ausser dem Ring, der sich dreht.
"Washer will go concave side down": Die Federscheibe geht mit der "hohlen" Seite (mit den gebogenen Zungen) nach unten (bei Kamera in Aufnahmehaltung) rein.
Es scheint als sei die Federscheibe auch schon einmal verkehrt rum drin gewesen.
Ich vermisse an der Unterseite der Skalenscheibe eine eindeutige From, die zum sie tragenden Pfosten paßt (was hat sich Herr Yashica da gedacht?)
Anhang 142031
Anhang 142029
Wenn die Schraube nicht im Gewinde des Pfostens hält, oder der Pfosten sich mitdreht, dann ist etwas "kaputt", dann kommt der KRAGLE (Lego Movie, eine geknitterte Tube KrazyGlue = Sekundenkleber) ins Spielt oder vielleicht im Guten erstmal Pattex oder ein ähnlicher, leichter wieder zu entfernender Kleber.
Anhang 142030
Der Pfosten dreht nicht mit und die Schraube hält im Gewinde?
Dann:
Federscheibe mit Zungen nach unten einlegen
Skalenscheibe einlegen und aufpassen, daß die Federscheibe nicht eingeklemmt wird
Schraube ansetzen und festziehen.
Ergebnis?
"Geht 3 Sekunden, dann löst sich die Schraube": Schraube mit Nagellack (im Gewinde) gegen Lösen sichern.
"Schraube klemmt nicht doll genug": Skalenscheibe mit einem Tröpfchen Pattex (ohne nebenbei zu kleckern!) oder doppelseitigem Klebeband am "Pfosten" sichern, Schraube wieder fest anziehen und ggf. mit Nagellack sichern.
Liste der Anhänge anzeigen (Anzahl: 1)
Zitat:
Zitat von
waldbeutler
Die ASA-Scheibe hat (auf ihrer Rückseite links oben erkennbar) ein Loch, in das ein Zapfen als Verdrehsicherung greifen muss, der auf der Oberseite der Zwischenscheibe mit rechteckiger Aussparung unten sein müsste.
Schau mal da genau nach: Sieht man da einen abgeriebenen / abgescherten Stummel eines Zapfens?
Wenn Du die Kamera kennst, dann beuge ich mich Deinem Rat!
Sonst wäre meine Ferndiagnose:
Anhang 142033
Plan B wäre noch (je nach Lage in der Realität!), die Skalenscheibe an die "Verdrehsicherung am Pfosten" zwar "anzupassen".
ASA-Einstellscheibe evtl. abnehmen evtl. in situ lassen
Skalenscheibe auflegen und mit einer Schraube aus dem Fundus mit einem kleineren Kopf fixieren
an den Stellen/Seiten wo der Pfosten die Abplattungen hat, den Urmacherschraubendreher ansetzen einmal mit dem 50g Hämmerchen oben auf den Schraubendreher klopfen und die Skalenscheib nach unten treiben (dazu müssen die Durchmesser Pfosten / Durchmesser Loch in Skalenscheibe passen! Das ist aus der Ferne bei der bisherigen Fotolage schwer zu sagen).
Hinterher die Schandtat mit der alten größeren Formschraube dezent abdecken.